Delock Interruttore di alimentazione WLAN MQTT con monitoraggio dell'energia
Descrizione
Questo interruttore della presa di alimentazione Delock può essere controllato tramite pulsante o WLAN. Con il firmware Tasmota installato, l'interruttore può essere facilmente integrato in sistemi esistenti per la domotica, IoT o M2M. Con l'aiuto dell'interfaccia web, la presa di corrente può essere controllata senza dover fare affidamento al cloud o un'applicazione.
Monitoraggio dei consumi energetici
Si può determinare il consumo di corrente alla presa di corrente a colpo d'occhio. In questo modo si può valutare l'efficienza energetica e i costi, nonché rilevare condizioni di funzionamento inusuali.
Specifiche
- Connettori:
1 x spina - CEE 7/4
1 x spina CEE 7/3 - Pulsante con indicatore LED a 2 colori
- Interfaccia Web
- Controllo timer programmabile
- Monitoraggio dei consumi energetici:
Tensione, corrente e potenza
Consumo in kwh - Supporta MQ Telemetry Transport (MQTT), Domoticz, Home Assistant
- Supporta Alexa
- Chipset: ESP8285
- Compatibile con gli standard IEEE 802.11 n/b/g, 802.3, 802.3 u
- Gamma di frequenza: 2,4 GHz
- Potenza di trasmissione (EIRP): 100 mW
- Adatto per uso interno
- Consumo: max. 1,5 W
- Tensione di ingresso: 230 V
- Corrente: max. 16 A
- Potenza di uscita: max. 2500 W
- Dimensioni senza spina: diametro ca. 51 mm, altezza ca. 45 mm
Requisiti di sistema
- Gateway WLAN
Contenuto della confezione
- Interruttore presa di alimentazione WLAN
- Manuale utente
Pacchetto
- Retail Box
Technical characteristics
Frequency range
• 2.4 GHz band
Physical characteristics
Diameter
• 51 mm
Height
• 45 mm
Colour
• bianco
25.01.2023
Datenblatt
25.01.2023
Data sheet
25.01.2023
Dane produktu
25.01.2023
Popis produktu
25.01.2023
Feuille de données
25.01.2023
Hoja de datos
25.01.2023
Datablad
25.01.2023
Adatlap
25.01.2023
Kataloški list
25.01.2023
Φύλλο δεδομένων
25.01.2023
Scheda tecnica
25.01.2023
Fișă cu date
17.11.2021
CE - Declaration of conformity
1.54 MB
08.10.2018
GPL
39.41 kB
15.11.2022
User Manual Multilingual
754.99 kB
What is the user name for the web interface if a password has been assigned?
The default user name is "admin".
The energy monitoring is not accurate.
Due to component tolerances and manufacturing, the device allows only an approximate measurement of the power. If necessary, e.g. after a reset, it is possible to obtain a better result by calibration: https://tasmota.github.io/docs/Power-Monitoring-Calibration/
Alternatively you can use a rough estimate with following console commands: CurrentCal 3300, PowerCal 10000, VoltageCal 1650.
Alternatively you can use a rough estimate with following console commands: CurrentCal 3300, PowerCal 10000, VoltageCal 1650.
How to flash the device to the latest Tasmota version?
For the socket switch we use a version of Tasmota, that we have adjusted and tested. Please understand that we can only support this Tasmota version.
What are the changes in firmware 6.7.1?
• Fix WeMo emulation for 1G echo and 2G echo dot.
• Add command "time" to disable NTP and set UTC time.
• Removed support for WPS.
• Add command "time" to disable NTP and set UTC time.
• Removed support for WPS.
What are the changes in firmware 7.2?
• Change default GUI to dark theme
• New Arduino Core version
• The LED is now controlled in the same way as Tasmota
• For the hardware configuration a user template is now used.
We recommend you save the device settings and do a "Reset 6" as console command. This will restore the default settings, but keep the WIFI SSID and Password.
• New Arduino Core version
• The LED is now controlled in the same way as Tasmota
• For the hardware configuration a user template is now used.
We recommend you save the device settings and do a "Reset 6" as console command. This will restore the default settings, but keep the WIFI SSID and Password.
Weaker Wi-Fi signal after firmware upgrade
The Wi-Fi calibration needs to be deleted to force the device to re-calibrate Wi-Fi after it restarts.
1. Run "reset 3" in the Console (your existing settings will not be affected).
2. The device will restart
3. Cycle the power on the device (unplug and plug it).
Wi-Fi calibration will not be done unless the device performs a cold boot from power up.
1. Run "reset 3" in the Console (your existing settings will not be affected).
2. The device will restart
3. Cycle the power on the device (unplug and plug it).
Wi-Fi calibration will not be done unless the device performs a cold boot from power up.
Configuration options
In case of problems, the following switches can help:
SetOption55 mDNS service 0 = disable 1 = enable
SetOption19 Set Home Assistant discovery protocol 0 = use Tasmota integration (default) 1 = use MQTT discovery
SetOption109 0 = (default) 1 = force gen1 Alexa mode, for Echo Dot 2nd gen devices only
SetOption55 mDNS service 0 = disable 1 = enable
SetOption19 Set Home Assistant discovery protocol 0 = use Tasmota integration (default) 1 = use MQTT discovery
SetOption109 0 = (default) 1 = force gen1 Alexa mode, for Echo Dot 2nd gen devices only
How to reset the energy values?
You can enter these console commands to reset the values for today1 / yesterday2 / total3:
"EnergyReset1 0" / "EnergyReset2 0" / "EnergyReset3 0".
"EnergyReset1 0" / "EnergyReset2 0" / "EnergyReset3 0".
The device does not connect to the Wi-Fi
If your device does not connect to your Wi-Fi and you've made sure the Wi-Fi credentials are correct, it is caused by using special chars or white spaces in your SSID or Password of your Wi-Fi. Remove them and try again. Other reason can be using an SSID longer than the allowed 32 characters.
articoli simili
Tutti i nomi e i simboli citati qui sono di proprietà dei rispettivi produttori. Salvo errori di stampa, modifiche ed errori.
Delock Interruttore presa di alimentazione WLAN MQTT
Articolo n. 11826
Delock Interruttore intelligente WLAN EASY-USB MQTT
Articolo n. 11828