Delock WLAN sklopka s utičnicom za napajanje MQTT

Predmet br. 11826
11826 Delock WLAN sklopka s utičnicom za napajanje MQTT
11826
11826
11826
11826
11826
11826
11826
11826 Delock WLAN sklopka s utičnicom za napajanje MQTT small 1
11826 small 2
11826 small 3
11826 small 4
11826 small 5
11826 small 6
11826 small 7
11826 small 8

Opis

Ova sklopka s utičnicom za napajanje tvrtke Delock može se regulirati gumbom ili WLAN-om. S ugrađenim upravljačkim softverom Tasmota sklopka se lako može ugraditi u postojeće automatske kućne sustave (IoT ili M2M). Uz pomoć mrežnog sučelja utičnica za napajanje može se regulirati bez korištenja usluge oblaka ili aplikacije.


Tehnički podaci

  • Priključak:
    1 x utikač CEE 7/4
    1 x utičnice CEE 7/3
  • Gumb sa sklopkom s 2-bojnim LED indikatorom
  • Mrežno sučelje
  • Programabilni tajmer
  • Podržava MQ Telemetry Transport (MQTT), Domoticz, Home Assistant
  • Podržava Alexa
  • Skup čipova: ESP8285
  • Kompatibilno s IEEE 802.11b/g/n
  • Frekvencijski opseg: 2,4 GHz
  • Snaga na predaji (EIRP): 100 mW
  • Za primjenu u zatvorenom
  • Utrošak snage: maks 1,5 W
  • Nazivna struja: 10 A / 250 V~
  • Nazivna snaga: 2500 W
  • Mjere (DxŠxV): oko 60 x 60 x 36 mm


Preduvjeti sustava

  • WLAN pristupnik


Sadržaj pakiranja

  • WLAN sklopka s utičnicom za napajanje
  • Korisnički priručnik


Pakiranje

  • Retail Box

Technical characteristics
Frequency range
• 2.4 GHz band
Physical characteristics
Duljina
• 60 mm
Width
• 60 mm
Height
• 36 mm
Boja
• bijela
What is the user name for the web interface if a password has been assigned? The default user name is "admin".
It is not possible to enter a WLAN password with an asterisk (*). The problem is solved with the current firmware version 6.5.0 since 22.10.19.
How to flash the device to the latest Tasmota version? For the socket switch we use a version of Tasmota, that we have adjusted and tested. Please understand that we can only support this Tasmota version.
What are the changes in firmware 6.7.1 since 6.3.20? • Fix WeMo emulation for 1G echo and 2G echo dot.
• Add command "time" to disable NTP and set UTC time
• Removed support for WPS.  
What are the changes in firmware 7.2? • Change default GUI to dark theme
• New Arduino Core version
• The LED is now controlled in the same way as Tasmota
• For the hardware configuration a user template is now used.
We recommend you save the device settings and do a "Reset 6" as console command. This will restore the default settings, but keep the WIFI SSID and Password.
Weaker Wi-Fi signal after firmware upgrade The Wi-Fi calibration needs to be deleted to force the device to re-calibrate Wi-Fi after it restarts.
1. Run "reset 3" in the Console (your existing settings will not be affected).
2. The device will restart
3. Cycle the power on the device (unplug and plug it).
Wi-Fi calibration will not be done unless the device performs a cold boot from power up.
 
Configuration options In case of problems, the following switches can help:
SetOption55 mDNS service 0 = disable 1 = enable
SetOption19 Set Home Assistant discovery protocol 0 = use Tasmota integration (default) 1 = use MQTT discovery
SetOption109 0 = (default) 1 = force gen1 Alexa mode, for Echo Dot 2nd gen devices only
The device does not connect to the Wi-Fi If your device does not connect to your Wi-Fi and you've made sure the Wi-Fi credentials are correct, it is caused by using special chars or white spaces in your SSID or Password of your Wi-Fi. Remove them and try again. Other reason can be using an SSID longer than the allowed 32 characters.
Svi ovdje spomenuti nazivi i simboli vlasništvo su odgovarajućih proizvođača. Greške u tisku,promjene i greške se izuzimaju.